#GARAGE DOOR TRIM SPLICE 2 PIECES HOW TO#
#GARAGE DOOR TRIM SPLICE 2 PIECES FULL#
#GARAGE DOOR TRIM SPLICE 2 PIECES FREE#

Steele offers more than 12,000 parts for cars and trucks as well as a large line of universal weatherstripping and rubber parts to be used on any project. Steele Rubber Products, located in Denver, NC, is a manufacturer and seller of high-quality rubber parts and weatherstripping products for classic and vintage automobiles, hot rods, RVs and Boats.

#GARAGE DOOR TRIM SPLICE 2 PIECES FULL#

Check out our YouTube channel for our full library of how-to/installation videos.

#GARAGE DOOR TRIM SPLICE 2 PIECES FREE#

If you have questions about Rubber Parts or Weatherstripping on your Classic Car, Truck, Hot Rod or even your boat, trailer or RV, feel free to reach out to us! You can call us at 80, contact us through our website or comment on this post and we’ll get you answers as quickly as possible. Steele not only has all the products you need but all the knowledge you need to get the job done right, too. Take your time and you should be happy with the outcome. Just remember, straight clean cuts that match and use the right adhesive for the job. The clear auto sealer should be available at any auto parts store. To ensure that the rubber will make a water tight seal when used as glass channel, apply a clear optical sealant between the glass and the rubber at the joint. If the joint was done properly, you should be able to pull on it without it failing. If there are any parts not adhered, apply a light amount with the paper clip to the void and apply pressure again. At this point you should have a good strong bond. Apply pressure from both ends to the splice. Carefully match the edges from one side to the other. If there is too much adhesive, it will not hold well. With a paper clip wire, spread the adhesive evenly over the surface, making sure it is covering the edges. Working on a flat surface makes the process of cutting and gluing easier.ģ. Put a small amount of glue on just one side of the splice joint. However, it will clean up using nail polish remover. It is clear in color and will stick your fingers together, just like “Super Glue”. Like all other adhesives, the less adhesive you use the better hold it has, especially with this Super Bonder. You should be able to find this at any hardware store that carries Loctite products or from the Steele Rubber Products site.Īfter cutting your weatherstrip, remember to test it for a profile match before proceeding. It is formulated for rubber-to-rubber bonding.

I found that for the best results, join them using Loctite Super Bonder 495. (8ft UPS max) If you cant find your profile online. (comparable to 25 - 26 gauge sheet metal) The pieces are available in lengths of 4ft, 6ft, and 8ft sections. The ends need to be clean cut and free of all debris. All aluminum trim is painted utilizing a baked enamel coating process and is warranted from chipping or cracking for 15 years. Best tool to cut both sponge and dense rubber? A utility cutter. If you put the ends together, all edges should match. It’s simple, your cut ends need to be straight. There are a few general rules to follow.ġ. However, when molding is not an option you can splice instead. This will give the best seal and have maximum strength at the joint. Now run out and cut a scarf joint just to try it.When you need an extrusion made into a ring or one piece unit, it is best to have the splice molded. This method works great with crown molding and just about any other molding you happen to need to put a seam into. Once you use a touch of white wood filler and paint that seam it should be nearly invisible.

Apply wood glue to one or the other end.

Cut both ends of your seam with the exact same setting.

See my post on cutting crown molding if you need a refresher.

Set up your miter saw with both a bevel and a miter.

That way they will fit together like a well oiled puzzle pieces. Leave the saw set up for whatever corner you just cut, it doesn’t matter what the settings are as long as you cut both ends of the seam with the exact same saw setting.

#GARAGE DOOR TRIM SPLICE 2 PIECES HOW TO#

How to cut a scarf joint in crown molding. With this method, once you use a little wood filler and paint, your seams will be nearly invisible! The technical term for this is a scarf joint. In this case, you’ll need a seam but you don’t want the seam to be visible. When you’re installing crown molding, sometimes you are working with a VERY LONG wall and you just can’t manage to get it covered with a single run of molding.

Maryville TN House Tour – Completed Rooms.

Garage door trim splice 2 pieces